TABLE I DIMENSIONS.
0S SHAFT (REF) |
0D FREE |
B LUG HEIGHT |
E LARGE SECTION HEIGHT |
J SMALL SECTION HEIGHT |
U 7/ THICKNESS AT BEVELED EDGE |
T 1/ THICKNESS |
0G |
W WIDTH |
0K 3/ |
0C 4/ CLEAR |
O 5/ TAKE UP |
R 6/ |
CH 6/ |
|||||||||
RECOMMENDED GROOVE (REF) |
OF RETAINED PART (REF) |
|||||||||||||||||||||
INCH |
MM |
BASIC |
TOL |
BASIC |
TOL |
BASIC |
TOL |
BASIC |
TOL |
BASIC |
TOL |
BASIC |
TOL |
BASIC |
TOL |
BASIC |
TOL |
MIN |
MAX |
MAX |
MAX |
|
1.000 1.023 1.062 1.125 1.188 1.250 1.312 1.375 1.438 1.500 1.562 1.625 1.687 1.750 1.771 1.812 1.875 1.969 2.000 2.062 2.125 2.156 2.250 2.312 2.375 2.437 2.500 2.559 2.625 2.687 2.750 2.875 2.937 3.000 3.062 3.125 3.156 3.250 3.346 3.437 3.500 3.543 3.625 3.687 3.750 3.875 3.938 4.000 |
25.4 26.0 27.0 28.6 30.2 31.7 33.3 34.9 36.5 38.1 39.7 41.3 42.9 44.4 45.0 46.0 47.6 50.0 50.8 52.4 54.0 54.8 57.1 58.7 60.3 61.9 63.5 65.0 66.7 68.3 69.8 73.0 74.6 76.2 77.8 79.4 80.2 82.5 85.0 87.3 88.9 90.0 92.0 93.7 95.2 98.4 100.0 101.6 |
.925 .946 .982 1.042 1.098 1.156 1.214 1.272 1.333 1.387 1.446 1.503 1.560 1.618 1.637 1.675 1.735 1.819 1.850 1.906 1.964 1.993 2.081 2.139 2.197 2.255 2.313 2.377 2.428 2.485 2.543 2.659 2.717 2.775 2.832 2.892 2.920 3.006 3.092 3.179 3.237 3.277 3.352 3.410 3.468 3.584 3.642 3.700 |
+.005 -.010 |
.167 .168 .181 .182 .182 .183 .183 .184 .184 .214 .235 .235 .235 .237 .237 .238 .239 .245 .239 .266 .266 .266 .267 .267 .267 .268 .268 .268 .268 .268 .310 .308 .308 .308 .298 .308 .308 .308 .308 .308 .328 .328 .328 .330 .332 .330 .342 .352 |
±.004 |
.116 .118 .122 .129 .132 .140 .146 .152 .160 .168 .172 .180 .184 .188 .190 .192 .196 .200 .204 .208 .212 .212 .220 .222 .224 .228 .232 .238 .242 .246 .248 .256 .260 .264 .252 .272 .274 .280 .286 .292 .285 .288 .296 .302 .310 .318 .318 .318 |
±.005 |
.065 ,066 .069 .071 .072 .076 .076 .082 .086 .091 .093 ,097 .099 .101 .102 .102 .104 .106 .108 .111 .113 .113 .116 .118 .119 .120 .122 .125 .127 .129 .131 .133 .136 .138 .131 .141 .143 .145 .147 .148 .148 .149 .153 .156 .160 .163 .163 .163 |
±.005 |
.034 .033 .041 .041 .041 .040 .039 .039 .039 .038 .049 .049 .048 .048 .048 .048 .048 .047 .047 .062 .062 .062 .061 .060 .060 .060 .059 .059 .059 .059 .073 .072 .072 .071 .071 ,070 .070 .070 .069 .069 .084 .084 .083 .083 .082 .082 .081 .081 |
±.001 |
.042 .042 .050 .050 .050 .050 .050 .050 .050 .050 .062 .062 .062 .062 .062 .062 .062 .062 .062 .078 .078 .078 .078 .078 .078 .078 .078 .078 .078 .078 .093 .093 .093 .093 .093 .093 .093 .093 .093 .093 .109 .109 .109 .109 .109 .109 .109 .109 |
±.002 |
.930 .951 .992 1.051 1.108 1.166 1.224 1.282 1.343 1.397 1.459 1.516 1.573 1.631 1.650 1.688 1.748 1.832 1.863 1.921 1.979 2.008 2.096 2.154 2.212 2.270 2.328 2.397 2.448 2.505 2.563 2.679 2.737 2.795 2.852 2.912 2.940 3.026 3.112 3.199 3.257 3.297 3.372 3.430 3.488 3.604 3.662 3.720 |
+.000 -.003 .004 FIM 2/ |
.037 .036 .044 .044 .044 .043 .042 .042 .042 .041 .053 .053 .052 .052 .052 .052 .052 .051 .051 .067 .067 .067 .066 .065 .065 .065 .064 .064 .064 .064 .079 .078 .078 .077 .077 .076 .076 .076 .075 .075 .091 .091 .090 .090 .089 .089 .088 .088 |
+.002 -.000 |
1.144 1.170 1.217 1.286 1.351 1.424 1.490 1.562 1.636 1.706 1.778 1.849 1.912 1.981 2.004 2.047 2.114 2.209 2.246 2.315 2.386 2.410 2.513 2.577 2.640 2.706 2.772 2.845 2.910 2.975 3.041 3.172 3.239 3.306 3.347 3.439 3.469 3.571 3.669 3.767 3.821 3.866 3.956 4.026 4.098 4.229 4.290 4.350 |
1.410 1.430 1.500 1.550 1.610 1.690 1.750 1.800 1.870 1.990 2.100 2.170 2.240 2.310 2.330 2.380 2.440 2.540 2.550 2.680 2.750 2.780 2.870 2.940 3.010 3.070 3.120 3.180 3.230 3.320 3.440 3.570 3.640 3.690 3.740 3.820 3.830 3.940 4.040 4.140 4.250 4.290 4.370 4.430 4.500 4.600 4.700 4.780 |
.005 .005 .005 .005 .005 .005 .006 .006 .006 .007 .007 .007 .007 .008 .008 .008 .008 .009 .009 .009 .010 .010 .010 .010 .011 .011 .011 .011 .011 .012 .012 .013 .013 .013 .014 .014 .014 .015 .015 .016 .016 .016 .017 .017 .017 .018 .018 .019 |
.057 .058 .060 .063 .064 .068 .068 .072 .076 .079 .082 .087 .090 .091 .092 .092 .094 .094 .096 .098 .098 .097 .100 .100 .100 .102 .104 .108 .109 .111 .112 .115 .116 .117 .107 .120 .120 .123 .126 .129 .122 .123 .127 .129 .133 .137 .137 .135 |
.034 .035 .036 .038 .038 .041 .041 .043 .045 .047 .049 .052 .054 .054 .055 .055 .056 .056 .057 .059 .059 .058 .060 .060 .060 .061 .062 .065 .066 .067 .067 .069 .070 .070 .064 .072 .072 .074 .076 .077 .073 .074 .076 .078 .080 .082 .082 .081 |
|
+.010 -.015 |
±.006 |
±.006 |
||||||||||||||||||||
|
+.000 -.004 .005 FIM 2/ |
||||||||||||||||||||||
+.013 -.020 |
±.003 |
+.000 -.005 .005 FIM 2/ |
||||||||||||||||||||
+.015 -.025 |
±.005 |
±.007 |
±.007 |
±.0015 |
+.000 -.006 .006 FIM 2/ |
+.002 5 -.000 |
||||||||||||||||
+.020 -.030 |
||||||||||||||||||||||
|
±.002 |
||||||||||||||||||||||
±.008 |
±.008 |
|||||||||||||||||||||
±.0025 |
+.003 -.000 |
|||||||||||||||||||||
1/ T - THICKNESS "T" APPLIES TO UNPLATED RINGS. FOR CORROSION RESISTANT STEEL AND PLATED RINGS, +.002 SHOULD BE ADDED TO THE MAXIMUM TOLERANCE, i.e. ±.002 SHOULD BE +.004/-.002.
2/ FIM - (FULL INDICATOR MOVEMENT) IS THE MAXIMUM ALLOWABLE DEVIATION OF CONCENTRICITY BETWEEN THE GROOVE AND THE SHAFT.
3/ K - MAXIMUM DIAMETER WHEN THE RING IS PROPERLY SEATED AT THE MINIMUM POSITION HALF WAY DOWM IN THE GROOVE.
4/ C - CLEARANCE DIAMETER WHEN THE RING IS SPRUNG OVER THE SHAFT PRIOR TO INSTALLATION INTO THE GROOVE. (DESIGN REFERENCE DIMENSION).
5/ O - END PLAY TAKE.
6/ R AND CH - RADII OR CHAMFERS ALLOWABLE ON PARTS TO BE RETAINED BY THE RINGS. THRUST LOADS OF RINGS, RETAINING PARTS WITH CORNER RADII OR CHAMFERS ARE TABULATED ON PAGE 6.
7/ 15° AND U - THESE DIMENSIONS ARE FOR GROOVE LOCATION CALCULATIONS ONLY (SEE (f) ON PAGE 7) AND NOT FOR INSPECTION PURPOSES.
.
For Parts Inquires call Parts Hangar, Inc (727) 493-0744
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business