MS16632C
TABLE I. DIMENSIONS.
0S SHAFT (REF) |
0D FREE |
E LARGE HEIGHT |
T 1/ THICKNESS |
0G |
W WIDTH |
R 3/ |
CH 3/ |
||||||
RECOMMENDED GROOVE (REF) |
OF RETAINED PART (REF) |
||||||||||||
INCH |
MM |
BASIC |
TOL |
BASIC |
TOL |
BASIC |
TOL |
BASIC |
TOL |
BASIC |
TOL |
MAX |
MAX |
.125 .156 .188 .219 .236 .250 .281 .312 .375 .406 .438 .500 .562 .625 .688 .750 .812 .875 .938 1.000 1.125 1.250 1.375 1.500 1.750 2.000 |
3.2 4.0 4.8 5.6 6.0 6.4 7.1 7.9 9.5 10.3 11.1 12.7 14.3 15.9 17.5 19.0 20.6 22.2 23.8 25.4 28.6 31.7 34.9 38.1 44.4 50.8 |
.102 .131 .161 .187 .203 .211 .242 .270 .328 .359 .386 .441 .497 .553 .609 .665 .721 .777 .830 .887 .997 1.110 1.220 1.331 1.555 1.777 |
+.002 -.004 |
.031 .037 .042 .044 .046 .050 .052 .053 .060 .063 .065 .070 .078 .081 .086 .090 .097 .105 .112 .120 .135 .150 .165 .180 .210 .240 |
±.003 |
.015 .015 .015 .025 .025 .025 .025 .025 .025 .025 .025 .035 .035 .035 .042 .042 .042 .042 .042 .042 .050 .050 .050 .050 .062 .062 |
±.002 |
.106 .135 .165 .193 .208 .220 .247 .276 .335 .364 .393 .450 .507 .563 .619 .676 .732 .789 .843 .900 1.013 1.126 1.237 1.350 1.576 1.800 |
±.0015 .0015 FIM 2/ |
.020 .020 .020 .030 .030 .030 .030 .030 .030 .030 .030 .040 .040 .040 .047 .047 .047 .047 .047 .047 .056 .056 .056 .056 .068 .068 |
+.002 -.000 |
.014 .018 .021 .021 .022 ,023 .021 .024 .026 .027 .029 .030 .033 .033 .034 .036 .038 .040 .043 .046 .052 .057 .062 .069 .081 .091 |
.011 .014 .016 .016 .017 .018 .016 .018 .020 .021 .022 .023 .025 .025 .026 .027 .029 .031 .033 .035 .040 .044 .048 .053 .062 .070 |
|
+.003 -.005 |
±.002 .002 FIM 2/ |
+.003 -.000 |
|||||||||||
|
±.004 |
|||||||||||||
±.006 |
±.005 |
±.003 .004 FIM 2/ |
|||||||||||
|
±.007 |
|||||||||||||
|
±.008 |
±.007 |
±.004 .005 FIM 2/ |
+.004 -.000 |
||||||||||
±.010 |
±.003 |
±.005 .005 FIM 2/ |
|||||||||||
1/ T - THICKNESS "T" APPLIES TO UNPLATED RINGS. FOR CORROSION RESISTANT STEEL AND PLATED RINGS, +.002 SHOULD BE ADDED TO THE MAXIMUM TOLERANCE, i.e. ±.002 SHOULD BE +.004/-.002.
2/ FIM - (FULL INDICATOR MOVEMENT) IS THE MAXIMUM ALLOWABLE DEVIATION OF CONCENTRICITY BETWEEN THE GROOVE AND THE SHAFT.
3/ R AND CH - RADII OR CHAMFERS ALLOWABLE ON PARTS TO BE RETAINED BY THE RINGS. ALLOWABLE THRUST LOADS FOR RINGS RETAINING PARTS WITH MAXIMUM CORNER RADII OR CHAMFERS ARE LSTED IN TABLE VI ON PAGE 8.
2
For Parts Inquires call Parts Hangar, Inc (727) 493-0744
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business