MS16634C
TABLE 1 DIMENSIONS.
0S SHAFT (REF) |
0D FREE |
E LARGE HEIGHT |
T 1/ THICKNESS |
P OVERALL BOW HEIGHT |
0G |
W WIDTH |
O 3/ TAKE UP |
R 4/ |
CH 4/ |
||||||
RECOMMENDED GROOVE (REF) |
OF RETAINED PART (REF) |
||||||||||||||
INCH |
MM |
BASIC |
TOL |
(REF) |
BASIC |
TOL |
BASIC |
TOL |
BASIC |
TOL |
BASIC |
TOL |
MAX |
MAX |
MAX |
|
.110 .125 .140 .156 .172 .188 .219 .250 .312 .375 .438 .500 .625 .744 .750 .875 .984 1.188 1.375 |
2.8 3.2 3.6 4.0 4.3 4.8 5.6 6.4 7.9 9.5 11.1 12.7 15.9 18.9 19.0 22.2 25.0 30.2 34.9 |
.076 .094 .102 .114 .125 .145 .185 .207 .243 .300 .337 .392 .480 .616 .547 .688 .822 1.066 1.213 |
+.002 -.003 |
.155 .073 .090 .090 .099 .101 .132 .167 .136 .188 .183 .213 .240 .202 .283 .326 .349 .297 .348 |
.010 .010 .015 .015 .015 .015 .015 .025 .025 .035 .035 .042 .042 .050 ,050 .050 .050 .062 .062 |
±.001 |
.030 .030 .033 .035 .037 .038 .051 .058 .058 .068 .068 .084 .089 .100 .100 .100 .100 .124 .124 |
±.005 |
.079 .096 .105 .116 .127 .147 .188 .210 .250 .303 .343 .396 .485 .625 .580 .675 .835 1.079 1.230 |
+.002 -.000 .0015 FIM 2/ |
.035 .022 .025 .027 .029 .030 .040 .049 .047 .060 .060 .073 .077 .085 .085 .085 .085 .107 .107 |
+.005 -.000 |
.013 .013 .014 .014 .016 .027 .026 .023 .023 .022 .022 .030 .035 .037 .037 .037 .037 .045 .045 |
.080 .040 .060 .060 .060 .060 .060 .060 .060 .065 .065 .080 .080 .060 .085 .085 .085 .090 .090 |
.060 .030 .045 .045 .045 .045 .045 .045 .045 .050 .050 .060 .060 .045 .065 .065 .065 .070 .070 |
±.002 |
±.005 |
+.003 -.000 .003 FIM 2/ |
|||||||||||||
+.007 -.008 |
|||||||||||||||
+.003 -.004 |
+.004 -.000 .004 FIM 2/ |
||||||||||||||
±.008 |
|||||||||||||||
±.009 |
|||||||||||||||
+.003 -.005 |
|||||||||||||||
±.010 |
|||||||||||||||
+.006 -.010 |
±.003 |
±.015 |
+.005 -.000 .005 FIM 2/ |
||||||||||||
1/ T - THICKNESS "T" APPLIES TO UNPLATED RINGS. FOR CORROSION RESISTANT STEEL AND PLATED RINGS, +.002 SHOULD BE ADDED TO THE MAXIMUM TOLERANCE, i.e. ±.002 SHOULD BE +.004/-.002.
2/ FIM - (FULL INDICATOR MOVEMENT) IS THE MAXIMUM ALLOWABLE DEVIATION OF CONCENTRICITY BETWEEN THE GROOVE AND THE SHAFT.
3/ O - END PLAY TAKE-UP (DESIGN REFERENCE DIMENSIONS).
4/ R AND CH - RADII OR CHAMFERS ALLOWABLE ON PARTS TO BE RETAINED BY THE RINGS. THRUST LOADS OF RINGS, RETAINING PARTS WITH CORNER RADII OR CHAMFERS, SEE NOTE (h) ON PAGE 7.
2
For Parts Inquires call Parts Hangar, Inc (727) 493-0744
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business