TABLE 1 DIMENSIONS.
0S SHAFT (REF) |
0D 1/ FREE (REF) |
A WIDTH ACROSS LUGS |
E |
T 2/ THICKNESS |
0G |
W WIDTH |
R 4/ |
CH 4/ |
||||||
RECOMMENDED GROOVE (REF) |
OF RETAINED PART (REF) |
|||||||||||||
INCH |
MM |
BASIC |
BASIC |
TOL. |
BASIC |
TOL. |
BASIC |
TOL. |
BASIC |
TOL. |
BASIC |
TOL. |
MAX. |
MAX. |
.469 .500 .594 .625 .669 .750 .781 .875 .984 1.000 1.125 1.188 1.250 1.375 1.500 1.562 1.625 1.750 1.772 1.875 1.969 2.000 2.125 2.156 2.250 2.375 2.500 2.625 2.750 2.875 3.000 3.250 3.375 |
11.9 12.7 15.1 15.9 17.0 19.0 19.8 22.2 25.0 25.4 28.6 30.2 31.7 34.9 38.1 39.7 41.3 44.4 45.0 47.6 50.0 50.8 54.0 54.8 57.1 60.3 63.5 66.7 69.8 73.0 76.2 82.5 85.7 |
.414 .459 .538 .569 .593 .673 .703 .796 .863 .863 1.002 1.064 1.126 1.250 1.374 1.412 1.474 1.597 1.597 1.721 1.779 1.809 1.933 1.933 2.057 2.180 2.304 2.428 2.518 2.642 2.754 3.013 3.114 |
.585 .625 .710 .740 .815 .894 .925 1.017 1.172 1.172 1.311 1.373 1.435 1.559 1.683 1.778 1.840 1.963 1.963 2.090 2.209 2.242 2.364 2.364 2.488 2.610 2.734 2.858 3.049 3.172 3.294 3.542 3.761 |
±.003 |
.105 .105 .105 .105 .135 .135 .135 .135 .188 .188 .188 .188 .188 .188 .188 .222 .222 .222 .222 .222 .262 .262 .262 .262 .262 .262 .262 .262 .323 .323 .329 .325 .395 |
±.005 |
.035 .035 .035 .035 .042 .042 .042 .042 .050 .050 .050 .050 .050 .050 .050 .062 .062 .062 .062 .062 .078 .078 .078 .078 .078 .078 .078 .078 .093 .093 .093 .093 .109 |
±.002 |
.419 .464 .544 .575 .599 .680 .711 .805 .872 .872 1.013 1.075 1.138 1.263 1.388 1.427 1.489 1.614 1.614 1.739 1.797 1.828 1.953 1.953 2.078 2.203 2.328 2.453 2.544 2.669 2.794 3.044 3.145 |
±.0015 .004 FIM 3/ |
.040 .040 .040 .040 .047 .047 .047 .047 .056 .056 .056 .056 .056 .056 .056 .068 .068 .068 .068 .068 .086 .086 .086 .086 .086 .086 .086 .086 .103 .103 .103 .103 .120 |
+.003 -.000 |
.052 .052 .052 .052 .065 .065 .065 .065 .086 .081 .086 .086 .086 .086 .086 .100 .100 .100 .094 .100 .114 .114 .114 .104 .114 .114 .114 .114 .143 .143 .143 .144 .182 |
.040 .040 .040 .040 .050 .050 .050 .050 .066 .062 .066 .066 .066 .066 .066 .077 .077 .077 .072 .077 .088 .088 .088 .080 .088 .088 .088 .088 .110 .110 .110 .111 .140 |
±.004 |
||||||||||||||
±.005 |
±.006 |
±.002 .004 FIM 3/ |
||||||||||||
±.006 |
||||||||||||||
±.003 .004 FIM 3/ |
+.004 -.000 |
|||||||||||||
|
±.003 .005 FIM 3/ |
||||||||||||||
|
±.007 |
||||||||||||||
±.008 |
±.007 |
±.003 |
±.005 .005 FIM 3/ |
|||||||||||
+.005 -.000 |
||||||||||||||
±.010 |
||||||||||||||
±.005 .006 FIM 3/ |
||||||||||||||
±.012 |
±.008 |
±.006 .006 FIM 3/ |
||||||||||||
±.015 |
||||||||||||||
1/ 0D = DIMENSION "D" SHOULD NOT BE USED AS PART OF AN INSPECTION PROCEDURE, USE DIMENSION "A".
2/ T = THICKNESS "T" APPLIES TO UNPLATED RINGS. FOR CORROSION RESISTANT STEEL AND PLATED RINGS, +.002 SHOULD BE ADDED TO THE MAXIMUM TOLERANCE, i.e. ±.002 SHOULD BE +.004/-.002.
3/ FIM = (FULL INDICATOR MOVEMENT) IS THE MAXIMUM ALLOWABLE DEVIATION OF CONCENTRTICITY BETWEEN THE GROOVE AND THE SHAFT.
4/ R AND CH = RADII OR CHAMFERS ALLOWABLE ON PARTS TO BE RETAINED BY THE RINGS. THRUST LOADS FOR RINGS, RETAINING PARTS WITH CORNER RADII OR CHAMFERS, ARE TABULATED ON PAGE 8.
For Parts Inquires call Parts Hangar, Inc (727) 493-0744
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business