TABLE I DIMENSIONS.
0H HOUSING (REF) |
0D FREE |
B LUG HEIGHT |
E LARGE SECTION HEIGHT |
J SMALL SECTION HEIGHT |
T 1/ THICKNESS |
Y OVERALL BOW HEIGHT |
0G |
W WIDTH |
K 3/ |
0C 4/ CLEAR |
X |
O 5/ TAKE UP OF L AND M |
R 6/ |
CH 6/ |
||||||||||
RECOMMENDED GROOVE (REF) |
OF RETAINED PART (REF) |
|||||||||||||||||||||||
INCH |
MM |
BASIC |
TOL |
BASIC |
TOL |
BASIC |
TOL |
BASIC |
TOL |
BASIC |
TOL |
BASIC |
TOL |
BASIC |
TOL |
BASIC |
TOL |
MIN |
MAX |
MIN |
MAX |
MAX |
MAX |
|
.250 .312 .375 .438 .453 .500 .512 .562 .625 .688 .750 .777 .812 .866 .875 .901 .938 1.000 1.023 1.062 1.125 1.181 1.188 1.250 1.259 1.312 1.375 1.378 1.438 1.456 1.500 |
6.4 7.7 9.5 11.1 11.5 12.7 13.0 14.3 15.9 17.5 19.0 19.7 20.6 22.0 22.2 22.9 23.6 25.4 26.0 27.0 28.6 30.0 30.2 31.7 32.0 33.3 34.9 35.0 36.5 37.0 38.1 |
.280 .346 .415 .482 .498 .548 .560 .620 .694 .763 .831 .859 .901 .961 .971 1.000 1.041 1.111 1.136 1.180 1.249 1.319 1.319 1.388 1.388 1.456 1.526 1.526 1.596 1.616 1.660 |
±.010 |
.065 .066 .082 .098 .098 .114 .114 .132 .132 .132 .142 .146 .155 .155 .155 .155 .155 .155 .155 .180 .180 .180 .180 .180 .180 .180 .180 .180 .180 .180 .180 |
±.003 |
.025 .033 .040 .049 .050 .053 .053 .053 .060 .063 .070 .074 .077 .081 .084 .087 .091 .104 .106 .110 .116 .120 .120 .124 .124 .124 .130 .130 .133 .133 ,133 |
±.002 |
.015 .018 .028 .029 .030 .035 .035 .035 .035 .036 .040 .044 .044 .045 .045 .047 .050 .052 .054 .055 .057 .058 .058 .062 .062 .062 .063 .063 .065 .065 .066 |
±.002 |
.015 .015 .025 .025 .025 .035 .035 .035 .035 .035 .035 .042 .042 .042 .042 .042 .042 .042 .042 .050 .050 .050 .050 .050 .050 .050 .050 .050 .050 .050 .050 |
±.002 |
.036 |
±.006 |
.268 .330 .397 .461 .477 .530 .542 .596 .665 .732 .796 .825 .862 .920 .931 .959 1.000 1.066 1.091 1.130 1.197 1.255 1.262 1.330 1.339 1.396 1.461 1.464 1.528 1.548 1.594 |
±.001 .0015 FIM 2/ |
.030 .030 .040 .040 .040 .055 .055 .055 .055 .055 .055 .062 .062 .062 .062 .062 .062 .062 .062 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 |
+.002 -.000 |
.047 .055 .063 .063 .071 .090 .092 .095 .104 .118 ,143 .145 .153 .172 .179 .188 .200 .212 .220 .213 .232 .226 .245 .265 .290 .284 .297 .305 .313 .320 .340 |
.115 .173 .204 .23 .25 .26 .27 .275 .34 .40 .45 .475 .49 .54 .545 .565 .61 .665 .69 .685 .745 .79 .80 .875 .885 .93 .99 .99 1.06 1.08 1.12 |
.020 .020 .030 .030 .030 .042 .042 .042 .042 .042 .042 .049 .049 .049 .049 .049 .049 .049 .049 .057 .057 .057 .057 .057 .057 .057 .057 .057 .057 .057 .057 |
.028 .028 .038 .038 .038 ,053 .053 .053 .053 .053 .053 .060 .060 .060 .060 .060 .060 .060 .060 .068 .068 .068 .068 .068 .068 .068 .068 .068 .068 .068 .068 |
.008 |
.011 .016 .023 .027 .027 .027 .027 .027 .027 .027 .032 .035 .035 .035 .035 .038 .038 .042 .042 .044 .047 .047 .047 .048 .048 .048 .048 .048 .048 .048 .048 |
.0085 .013 .018 .021 .021 .021 .021 .021 .021 .021 .025 .028 .028 .028 .028 .030 .030 .034 .034 .035 .036 .036 .036 .038 .038 .038 .038 .038 .038 .038 .038 |
±.003 |
±.003 |
.047 |
±.006 |
+.003 -.000 |
||||||||||||||||||||
±.002 .002 FIM 2/ |
||||||||||||||||||||||||
±.004 |
±.004 |
.063 |
±.007 |
±.002 .004 FIM 2/ |
.011 |
|||||||||||||||||||
±.005 |
||||||||||||||||||||||||
±.005 |
±.005 |
.073 |
±.008 |
±.003 .004 FIM 2/ |
||||||||||||||||||||
±.015 |
||||||||||||||||||||||||
±.025 |
±.006 |
±.006 |
.085 |
±.012 |
±.004 .005 FIM 2/ |
|||||||||||||||||||
1/ T - THICKNESS "T" APPLIES TO UNPLATED RINGS. FOR CORROSION RESISTANT STEEL AND PLATED RINGS, +.002 SHOULD BE ADDED TO THE MAXIMUM
TOLERANCE, i.e. ±.002 SHOULD BE +.004/-.002.
2/ FIM - (FULL INDICATOR MOVEMENT) IS THE MAXIMUM ALLOWABLE DEVIATION OF CONCENTRICITY BETWEEN THE GROOVE AND THE HOUSING.
3/ K - MNIMUM GAP WIDTH WHEN THE RING IS PROPERLY SEATED IN THE GROOVE. (DESIGN REFERENCE DIMENSION).
4/ C - ACTUAL CLEARANCE DIAMETER WHEN THE RING IS SPRUNG INTO THE HOUSING, PRIOR TO INSTALLATION INTO THE GROOVE. (DESIGN REFERENCE DIMENSION).
5/ O - END PLAY TAKE UP (DESIGN REFERENCE DIMENSION).
6/ R AND CH - RADII OR CHAMFERS ALLOWABLE ON PARTS TO BE RETAINED BY THE RING. THRUST LOADS OF RINGS, RETAINING PARTS WITH CORNER RADII OR CHAMFERS ARE TABULATED ON PAGE 6.
.
For Parts Inquires call Parts Hangar, Inc (727) 493-0744
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business