TABLE I DIMENSIONS.
0S SHAFT (REF) |
0D FREE |
B LUG HEIGHT |
E LARGE HEIGHT |
J SMALL SECTION HEIGHT |
T 1/ THICKNESS |
0C 2/ CLEAR |
R 3/ |
CH 3/ |
0G |
W |
|||||||||
SHALLOW GROOVE (OPTIONAL) |
|||||||||||||||||||
OF RETAINED PART (REF) |
|||||||||||||||||||
WIDTH |
|||||||||||||||||||
INCH |
MM |
TOL |
BASIC |
TOL |
BASIC |
TOL |
BASIC |
TOL |
BASIC |
TOL |
BASIC |
TOL |
MAX |
MAX |
BASIC |
TOL |
BASIC |
TOL |
|
.094 .125 .156 .187 .250 .313 .376 .437 .500 .625 .750 |
2.4 3.2 4.0 4.8 6.3 7.9 9.5 11.1 12.7 15.9 19.0 |
±.002 |
.089 .120 .150 .181 .238 .298 .354 .412 .470 .593 .706 |
+.002 -.003 |
.078 .078 .078 .097 .097 .141 .141 .151 .158 .180 .233 |
±.008 |
.045 .070 .079 .086 .101 .114 .125 .138 .140 .175 .176 |
±.004 |
.028 .048 .051 .052 .057 .073 .075 .083 .082 .100 .104 |
±.004 |
.025 .025 .025 .035 .035 .042 .042 .050 .050 .062 .062 |
±.002 |
.26 .33 .36 .44 .49 .68 .74 .81 .90 1.06 1.32 |
.042 .054 .059 .063 .072 .080 .086 .093 .100 .120 .125 |
.025 .032 .035 .038 .043 .048 .051 .056 .060 .072 .075 |
SIZES .094 THROUGH .187 ARE NOT RECOMMENDED FOR USE WITH GROOVES |
|||
±.003 |
|||||||||||||||||||
+.002 -.004 |
|||||||||||||||||||
±.003 |
|||||||||||||||||||
±.005 |
±.005 |
.240 .303 .361 .419 .478 .599 .718 |
+.0005 -.0015 |
.041 .048 .048 .056 .056 .069 .069 |
+.003 -.000 |
||||||||||||||
|
±.003 |
+.003 -.005 |
±.004 |
|||||||||||||||||
+.001 -.002 |
+.004 -.000 |
||||||||||||||||||
+.004 -.006 |
±.006 |
±.006 |
|||||||||||||||||
±.004 |
|||||||||||||||||||
±.005 |
+.002 -.003 |
||||||||||||||||||
1/ T - THICKNESS "T" APPLIES TO UNPLATED RINGS. FOR CORROSION RESISTANT STEEL AND PLATED RINGS, +.002 SHOULD BE ADDED TO THE MAXIMUM TOLERANCE,
i.e. ±.002 SHOULD BE +.004/-.002.
2/ C - ACTUAL CLEARANCE DIAMETER WHEN THE RING IS SPRUNG OVER THE SHAFT. (DESIGN REFERENCE DIMENSION).
3/ R AND CH - RADII OR CHAMFERS ALLOWABLE ON PARTS TO BE RETAINED BY THE RINGS. THRUST LOADS FOR RINGS, RETAINING PARTS WITH CORNER RADII OR CHAMFERS, ARE TABULATED ON PAGE 6.
For Parts Inquires call Parts Hangar, Inc (727) 493-0744
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business